How to test a sewing machine pedal (2023)

This page is supported by our readers. If you buy through links, we may earn a commission at no cost to you.

You'll enjoy learning about the inside of your sewing machine's foot control, which may make testing and repairing easier than you'd like. think

There are specific steps to follow to adjust the foot control on your sewing machine which you can read about below.

The easiest and most effective way to test the sewing machine pedal is to use a tester. These devices provide information about the electrical components of a sewing machine's foot control.

You can find many types of testers including resistance testers, circuit testers, TVOMs, and continuity testers. So let's take a look at what it means to experiment with your sewing machine's foot control and how you can easily adjust the sewing speed.

Steps to test your sewing machine foot control

After choosing which test kit to use, use the setting that tests resistance in ohms. Connect the probes to the appropriate wires and press the pedal. If you press the pedal with everything connected, the test kit will give you the resistance in ohms.

If the meter gives a negative response, verify that the probes are correct and try again. If the readings are inaccurate, you should contact a repair shop to have the pedal repaired.

However, if the meter reads a positive result, you know it's working properly and there are no problems to fix.

In most cases, all you need to adjust the pedal is a screwdriver to make it faster or slower. To decelerate the pedal, open the pedal and realign the contact areas to ensure not too much force is being applied to the pedal.

It allows you to run a smaller power supply from the footswitch, allowing you to work more slowly. To use the pedal faster, open up the device and widen the contact point to allow for more lift.

Lots of pedals per PCB, but not always as not all have speed change capabilities.

You also want different sewing machines to have original designs that may require slightly different steps. So it might be a good idea to check with your sewing machine brand to feel more confident after getting advice from them directly.

If your specific sewing machine model allows for speed adjustments, service personnel can walk you through the steps to make changes or advise you to take it to their shop.

How to connect a pedal

There are so many sewing machine models with different spinning systems. On many models, the pedal has a power cord that connects to the motor cord.

Some models have one cord that plugs directly into the sewing machine and another motor cord that plugs into an outlet to power the foot control. If your machine has a different wiring system, you should consult the manual for more information.

If you have an older sewing machine, installing the foot control on newer models can help as there are fewer simpler parts. Turn off the device and unplug the power cord before beginning the following steps.

Start by checking the power cord. In this case, replace it before turning on the machine again. Sometimes the pedal doesn't work because the cables have come loose.

This can ensure that the cables are correct. However, there are some sewing machines that require you to remove the circuit board to inspect the threads.

In some cases the pedal wiring is fine. In these cases, the pedal must be cleaned as it can become clogged.

Sewing machine pedal too fast solution

For those who find their pedal is working too fast, we recommend that you consult your owner's manual before proceeding. Manuals usually have full pedal speed details for you to make changes.

The manual will tell you if your model has a ESC or speed screw toggle feature. It's best to start with small adjustments as they can make a big difference when it comes to delaying a pedal.

On newer sewing machines with a built-in computer, you can usually change the speed with a speed change function. However, some models require maintenance. Take them to a shop to slow down the pedal.

You also need to know if your machine is industrial. This is because industrial sewing machines don't have speed change features as you designed them for speed.

What should you do if your sewing machine control pedal is stuck?

One of the first things we recommend you do to help loosen your foot grip is to use lube. Put some oil on the spring and rivets and see if you notice a difference.

For the cases where this doesn't work, it could mean the spring. By replacing the spring, your pedal can run smoother in no time. It's also worth checking if they're clogging the dock with dirt, as cleaning it can be an easy fix.

If you find that the spring isn't a problem; It's best to contact a mechanic to fix it or walk you through the steps to fix it as it can be a bit trickier.

How do you keep an eye on your sewing machine foot?

A great way to use your sewing machine. Keep the pedal in place by using a non-slip mat. This makes a big difference when your pedal is on a hard floor as the mat will keep the pedal from moving so you don't have to stop and readjust the position.

You can also use a footrest for the pedal. This can make it more comfortable to wear and keep it in place. When using a footrest, be careful not to lift the pedal too often as this can cause it to move more.

When using the footrest pedal, make sure your heel is on the floor or very close to the floor to avoid lifting your foot too high while sewing and causing the control pedal to move.

Can you protect your pedal from overheating?

Some people find that the foot controller gets hot when they use it sometimes. In most cases this is not a big problem as you can fix it yourself. When your pedal is overheating, it's usually due to loose connections or cables.

If the connections are loose, you can simply tighten them with a screwdriver. For broken connections, replace the monad.